This is a 0.96 inch OLED display module. The display module can be interfaced with any microcontroller using SPI/IIC protocols. The package includes d..
PSoC 4 an ARM based PSoCPSoC 5LP programmer and debuggerPower supply systemBluetooth interfaceArduino compatible headersDigilent Pmod compatible heade..
Specifications:Input any USB Port Like: Computer/ Laptop/ Color TV/ Car/ Aeroplane/ Audio/ VideoCharging Time: 4 Hours (approx) on 5V-1AmpMicro USB In..
The Radxa ROCK 4C+ is a Single Board Computer (SBC) in a credit card sized form factor
packed with a wide range of class‑leading functionality, featu..
The Raspberry Pi 4 Model B is the latest addition to the popular Raspberry Pi range of computers, offers a significant increase in processor speed, ri..
STM32F0DISCOVERY helps to discover the STM32F0 Cortex-M0 features and to develop applications easily. It includes everything required for beginners an..
Description: FlySky Introduces its newest 6 channel 2.4GHz system, The FS-T6. After years of success with the CT6B, FlySky presents the new FS-T6 with loads of cool and convenient features making the operation of this transmitter simple and instinctive.
The 6-channel FlySky FS-T6 is the perf..
Description:
This is a very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being app..
Description:
This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied ..
Description:
This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. The harder the force, the lower the resistance. When no pressure is being applied to the FSR its resi..
Package Contents
1 x Four Channel 12V ULN2003 Based Relay Board Module
Product Overview
Relay board module is used for controlling higher current loads from your microcontroller development board, PC parallel port or Arduino Uno. This board has four..
Description:
This is a basic, 4-digit 7-segment display - red in color. It has a common anode. The display features one decimal point per digit. The LED segments of the display require current-limiting resistors when powered from a 5 V logic pin. The value of the resistor is typically betwee..
Description:
Papilio One board fully assembled with a Xilinx XC3S250E and 4Mbit SST SPI Flash memory. Specifications Power Four independent power rails at 5V, 3.3V, 2.5V, and 1.2V. Power supplied by a power connector or USB. USB Two channel USB connection for JTAG and serial communications i..
Description:
Papilio One board fully assembled with a Xilinx XC3S500E and 4Mbit SST SPI Flash memory.
Features:
Power :Four independent power rails at 5V, 3.3V, 2.5V, and 1.2V. Power supplied by a power connector or USB.
USB :Two channel USB connection for JTAG and seri..
Description: This is FS-CT6B 6ch 2.4GHz transmitter & receiver It has 0.8W transmitter with range up to 1km line of sight.
Specifications:
Channels: 6
Frequency: 2.4GHz
Type 2 remote control. (Throttle on the left side)
Transmitter power: 0.8W
Requires 8 AA size batteries..
Description:
GPS tracker for Alzheimer's patient helps to track the location of patient in case if they move out of the safe zone. If the location is changed out of safe zone then message is sent via GSM modem regarding location of patient. This system is all integrated into Arduino UNO.
..
Description:
It is built with a stamp sized Quad Band GSM/GPRS engine - SIM900, works on frequencies 850/ 900/ 1800/ 1900 MHz. This shield fits on top of any classic Arduino or compatible, and packs a surprising amount of technology into it's little frame. This module can do just about ..