Menu
Your Cart

Atmega16/Atmega32 Project Development Board with Microcontroller IC

Atmega16/Atmega32 Project Development Board with Microcontroller IC
Atmega16/Atmega32 Project Development Board with Microcontroller IC
-30 %
Atmega16/Atmega32 Project Development Board with Microcontroller IC
Atmega16/Atmega32 Project Development Board with Microcontroller IC
Atmega16/Atmega32 Project Development Board with Microcontroller IC
  • Stock: In Stock
  • Brand: ElementzOnline
  • Model: ATMEGA16-32-PJT-BRD-with-IC
  • Weight: 200.00g
  • SKU: ATMEGA16-32-PJT-BRD-with-IC
Products Sold: 22
Product Views: 19410
₹699.00
₹999.00

Available Options

Product Overview

The ATMEGA Project Board is designed to work with ATMEGA16/32. The ATMEGA16/32 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. It executes powerful instructions in a single clock cycle and achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption.

The Project Board is equipped with standard JTAG (IEEE std. 1149.1 Compliant) for Programming & Debugging and 10 pin In-System Programming Interface (ISP) CONNECTOR for Programming using any AVR Serial Programmer such as USBasp. And the board by default has 8MHz Crystal.


Product Information 

  • Filter capacitor for brownout protection
  • On board 1 Ampere power supply using LM7805 voltage regulator
  • Power supply indicator using On-board LED
  • Input and Output filter capacitors
  • JTAG (IEEE std. 1149.1 Compliant) Interface for Programming and Debugging.
  • Standard 10-Pin ISP header for programming using USBasp
  • Standard 10-Pin JTAG header for programming using JTAG Debugger
  • I/O Expansion headers :-  • 32 Programmable I/O Lines   •  UART expansion (TTL compatible)  • Analog reference header
  • External Oscillator circuitry equipped for connecting Crystal Oscillators
  • Reset switch
  • Board Size: 8.5cm x 7cm
  • Operating Voltage : 5V (7805 on board)
  • Input Voltage : 7V - 35V DC adapter (preferably 12V/9V) 

or You can give 7V-35V DC directly to Vin lines (marked as 12V) on board 

or 5V DC directly to Vcc lines (marked as 5V) on board

(Make sure you connect the GROUND to GND line on board too)

INPUT VOLTAGE (12V/9V), REGULATED VOLTAGE(5V) and GND lines are extended on board itself. So if you need to give power to external sensors/boards, you don't need any external power supply boards

 "You can use 12V or 9V DC adapter and connect directly to DC jack on board (input to 7805) but if you are using 5V adapter, remove 7805 from board and short footprints of input (1) & output (3) pins of 7805 using a wire and then connect 5V to the DC power jack"

Package Contents

  • 1 x AVR 40pin ATMEGA16/32 PROJECT BOARD with JTAG & ISP
  • 1 x ATMEGA16A / ATMEGA32A MICROCONTROLLER IC (on board)
  • 1 x 8MHz Crystal Oscillator (on board soldered)
  • 1 x 7805 (on board soldered)
  • 1 x RESET SWITCH (on board soldered)
  • OTHER BASIC COMPONENTS and BERG STRIP EXTENSIONS (on board soldered)
  • 1 x FREE CONTAINER BOX

"Images are for illustration purposes only. Color of the PCB may be different from the one shown in the image"

"If you need a different crystal oscillator on board, you can contact us before making payment. If that particular crystal oscillator is available in stock with us, we can provide you the custom board with that particular crystal oscillator"


Write a review

Please login or register to review
Site uses Cookies
This site uses cookies to provide and improve your experience. By continuing to use this site, you agree to accept these cookies.